Custom Stamped Bent L-Shaped Bolts

Posted by alex@engineeredsource.com
On July 29, 2021
0 Comments

These custom stamped bent L-shaped bolts were manufactured with a cold formed/stamped stop shoulder critical to the assembly application. 5/16-18 thread was incorporated underneath the shoulder/flange feature, at approximately 14.42mm in length. The unthreaded length measures 31mm on the outside and the flange/shoulder diameter is 17.5mm. Zinc + clear finish was applied to complete the […]

Custom Large B7 Threaded Studs – 1-1/5 X 6-1/4″ With Zinc Clear Finish

Posted by alex@engineeredsource.com
On September 22, 2020
0 Comments

We had 64 pieces of these custom large B7 threaded studs manufactured for our customer, with the cut and chamfer of the plain parts done domestically followed by commercial zinc + clear plating operation. The threaded studs measured 1-1/5 – 8 X 6-1/4 and were supplied with ASTM A194 2H heavy hex nuts. The cut […]

Custom ACME Thread Studs – 1-1/4″ in A108 Steel Material

Posted by alex@engineeredsource.com
On May 26, 2020
0 Comments

These are large custom ACME thread studs we supplied our customer in two different lengths: 2 ft 11 inch and 3 ft 5 inch. Both lengths were fully threaded with 1-1/4″ ACME thread. 3 custom tapped heavy hex nuts per piece were supplied with the threaded studs. Parts were made in the USA and were […]

Custom Double End Shoulder Studs – A193 B7 Material

Posted by alex@engineeredsource.com
On November 5, 2019
0 Comments

These custom double end shoulder studs were manufactured domestically using B7 material with plain finish. 1″ coarse thread was incorporated on one side at a length of 1-1/4″. 1-5/8″ of 3/4″ coarse thread was cut on the other side of the stud, with the shoulder machined to a diameter of .75″ +/- .01″. Overall length […]

Large Double End Studs – 1″ to 1-1/8″ Diameter Partially Threaded Studs In Plain B7 Material

Posted by alex@engineeredsource.com
On October 26, 2018
0 Comments

We supplied our customer with 3 different sizes of these large double end studs: 160 pieces of 1″-8 X 5.125″ with 1-1/2″ and 1-3/4″ of thread lengths, 30 pieces of 3/4″-10 X 3.8125″ with 1″ and 1-1/4″ of thread lengths, and 12 pieces of 1-1/8″-8 X 5-3/4″ with 1-7/8″ and 1-1/4″ thread lengths. All threaded […]

Custom Stainless Double End Studs – 1/2-13 Double End Studs In 304 Stainless Steel Material

Posted by alex@engineeredsource.com
On June 11, 2018
0 Comments

These are custom stainless double end studs we provide our long time customer on a recurring basis, typically with production runs of approximately 300 pcs. They are made domestically using 304 stainless steel material. Pictured here is the threaded stud with it’s mating part. The thread on one side measures .875″ in length and approximately […]

Custom Stainless Steel Studs – 3/4 X 6 Inch 316 Stainless Steel Threaded Studs

Posted by alex@engineeredsource.com
On May 12, 2018
0 Comments

These are one of many custom stainless steel studs we supply our recurring customers. This specific order of 3/4″ X 6″ threaded studs in 316 stainless steel consisted of 42 pieces. Off the shelf 6 foot 316 stainless steel threaded rod was cut and chamfered on both sides – production took 4 days from receipt […]

Large Custom Double Sided Studs – Grade 8 1-1/4 X 52 Inch Overall Length

Posted by alex@engineeredsource.com
On October 6, 2017
0 Comments

These are large custom double sided studs made using grade 8 steel material at 1-1/4 diameter and 52 inches overall length. Each side had 6 inches of thread and a grade 8 nylon insert zinc yellow lock nut. Production for 8 pieces took approximately 1 week and all components were USA made. Material certs were […]

Custom 17-4 Stainless Steel Double End Threaded Studs – 1/2 X 7 With Coarse & Fine Threads

Posted by alex@engineeredsource.com
On August 8, 2017
0 Comments

These are custom 17-4 stainless steel double end threaded studs made using 17-4 H1100 stainless material with heat treat required to finalize the parts. 200 pieces of the custom threaded studs were made domestically with a lead time of 2-3 weeks from confirmation. 2-1/4 inches of 1/2 coarse thread is incorporated with 1-3/4 inches of […]

Custom Machined Double End Studs For Aerospace Applications – 630 (17-4) AMS 5643T Material With a Drilled Hole Per Print

Posted by alex@engineeredsource.com
On August 4, 2017
0 Comments

These are custom machined double end studs used for aerospace applications and in our case specifically for helicopter repair. 17-4 material is used and the 10-32 UNJF-3A thread is cut after the drilled hole process and machined operations are completed. A 3/32 hex recess with a .225″ deep cavity is created on one side using […]

Page 1 of 312 3